Product no.: 372
Exhaust under engine short, silencer insert removable
General note: The item offered is an item without e-marking / tuning item that is intended for racing purposes and customizing. Therefore, use on public roads is not permitted. The attachment leads to the expiry of the operating license unless it is entered into the vehicle documents by an approved TÜV testing center. |
67.90 €
*
In stock |
|
Product no.: 899
Kepspeed bench, diamond pattern, suitable for Skyteam Skymax with 5.5 liter frame. |
62.90 €
*
Still in stock |
Product no.: 215
Indicator light set suitable for Kepspeed lamp housing (2x indicators, neutral and high beam) |
13.90 €
*
In stock |
|
Product no.: 0122
Needle-bearing swingarm from Kepspeed
completely like photo
Dimensions of version +4
Total length: approx. 350mm
Length from center of swing arm axle - center of wheel mount: approx. 305mm
Dimensions of version +10
Total length: approx. 410mm
Length from center of swing arm axle - center of wheel mount: approx. 365mm
The swing arm is registered in the COC of the Kepspeed Custom Monkey and can therefore usually be registered in other vehicles without any problems. Please write to us about this and we will be happy to send you the COC by email. |
92.90 €
*
In stock |
Product no.: 1265b
Monkey aluminum swing arm + 4 cm with needle bearings Dimensions of version +4
Dimensions of version +10 The swing arm is registered in the COC of the Kepspeed Custom Monkey and can therefore usually be registered in other vehicles without any problems. Please write to us about this and we will be happy to send you the COC by email. |
92.90 €
*
In stock |
Product no.: 1352
45 km/h CDI installed as standard on the Kepspeed Dax (open by pulling out the plug), also suitable for larger engines, reduces the speed to approx. 6000 rpm |
27.90 €
*
In stock |
|
Product no.: 1277s
open stainless steel exhaust from Kepspeed GP 1, short rear silencer, additional silencer insert available in the shop (see accessories below) DB Killers with a diameter of 50-52mm fit Lambda sensor connection with M12x1.25 thread (see below under accessories for suitable lambda sensor, but a suitable screw for closing is also included so that the exhaust can also be used on other models) |
179.90 €
*
In stock |
|
Product no.: 1424
Bottom stainless steel exhaust for Monkey with E-No. (E-No. valid for Kepspeed Monkey 125ccm) without cat (for suitable cat see below under accessories) The exhaust is supplied with a lambda sensor adapter, but there is also a screw included to close the connection on the manifold The system does not fit the Euro 4 / 5 125ccm models without adjustment work because the manifold hits the brake pedal
|
229.90 €
*
Currently unavailable |
Product no.: 1144
CNC milled rim star from Kepspeed (for mounting Dax rims on Monkey wheel hub) available in black, silver, blue or gold |
49.90 €
*
In stock |
Product no.: 1119
Dax swingarm from Kepspeed in standard length Dimensions of version +0 The swing arm is registered in the COC of the Kepspeed Custom Dax and can therefore usually be registered in other vehicles without any problems. Please write to us about this and we will be happy to send you the COC by email. |
119.99 €
*
In stock |
Product no.: 1276
Mudguard holder from Kepspeed for 45 mm USD fork, for attaching the mudguard directly above the tire (clamp for 33mm tube) |
59.90 €
*
In stock |
|
Product no.: 1089b
Very high quality black Kepspeed aluminum swingarm for Dax + 6 cm for Honda Dax / Skyteam Dax / Skymax The included axle is the rear wheel axle Dimensions of version +6
The swing arm is registered in the COC of the Kepspeed Custom Dax and can therefore usually be registered in other vehicles without any problems. Please write to us about this and we will be happy to send you the COC by email. |
169.90 €
*
In stock |
|
Product no.: 1123
DAX swingarm from Kepspeed in + 10 cm Dimensions of version +10 A 12mm wheel axle is required with at least 210mm length (measured without head) |
121.90 €
*
In stock |
Product no.: 354-356
Low Monkey seat from Kepspeed, available with white, gray or black piping, diamond pattern |
59.90 €
*
In stock |
Product no.: 0705
Complete air filter as installed on Kepspeed or Skyteam Monkey, with 35mm connection, when used on original Honda carburettor (28mm connection) the Honda rubber flange is necessary
(See accessories below)
|
19.99 €
*
In stock |
|
Product no.: 1761
Keihin (China) carburetor PE28 for engines from 160-190cc Connection to the intake flange: approx. 35mm HD: 118 |
59.90 €
*
Still in stock |
|
Product no.: 1165
Kepspeed gearshift lever in gold Short version! Length from the middle of the mount to the middle of the switching rubber approx. 80mm |
21.99 €
*
Still in stock |
|
Product no.: 1140
offset sprocket kit from Kepspeed for the wide Dax and Monkey Kepspeed swingarms, normal sprockets can be used |
109.90 €
*
In stock |
|
Product no.: 499
Kepspeed chain tensioner 28 x 35 mm or 23 x 35mm |
12.90 €
/ pair(s)
*
In stock |
Product no.: 1423
overhead Kepspeed exhaust in stainless steel with E-No. E-No. for 50cc engine
Exhaust is not suitable for large engines due to the short manifold
The 58mm DB Killer from Kepspeed fits |
209.90 €
*
In stock |
|
Product no.: 0409/0410
Aluminum spacer for Monkey sprocket from Kepspeed available in 3 or 5 mm thickness
Suitable for Honda Monkey Z50A Z50J1 Z50 J2 Skyteam Monkey Skymini etc. |
20.90 €
*
In stock |
Product no.: 334
ALU clutch cover from Kepspeed, available in black, gold, blue, red or silver |
16.90 €
*
In stock |
Product no.: 1070/71B
High-quality black Kepspeed swingarm for Dax with a wide profile available in +2cm or +4cm Dimensions of version +2 Dimensions of version +4 |
129.90 €
*
Still in stock |
Product no.: 709b
Kepspeed under engine exhaust stainless steel
General note: The item offered is an item without e-marking / tuning item that is intended for racing purposes and customizing. Therefore, use on public roads is not permitted. The attachment leads to the expiry of the operating license unless it is entered into the vehicle documents by an approved TÜV testing center. |
199.90 €
179.90 €
*
You save 10 %
In stock |
|
Product no.: 1070/71
High-quality Kepspeed aluminum swingarm with wide profile available in + 4 or in +2 also available in black in the shop item number, 1070/71b Dimensions of version +2 Dimensions of version +4 |
119.90 €
*
Currently unavailable |
Product no.: 1781
Aluminum crash bar set for Monkey from Kepspeed (installed on Kepspeed Monkey in the picture) |
95.00 €
*
In stock |
|
Product no.: 1773
Kepspeed rear silencer noise 51mm connection suitable for Kepspeed manifolds underneath (complete system like 2nd photo also available in the shop) |
99.90 €
*
Still in stock |
|
Product no.: 1739-1746
Sprocket from Kepspeed for Dax for screwing made of high-strength aluminum in various sizes |
29.90 €
25.90 €
*
You save 13 %
In stock |
Product no.: 1747-1756
Kepspeed sprocket made of high-strength aluminum, available with 24, 26, 28, 29, 30, 31, 33, 35, 37 or 40 teeth The sprocket with 24T is closed, 24T and 26T are in silver and the other sprockets are in black |
29.90 €
25.90 €
*
You save 13 %
In stock |
Product no.: 1702
Kespeed Classic exhaust with snake manifold suitable for engines without electric start. Heat protection plate with e-number also available in the shop.
General note: The item offered is an item without e-marking / tuning item that is intended for racing purposes and customizing. Therefore, use on public roads is not permitted. The attachment leads to the expiry of the operating license unless it is entered into the vehicle documents by an approved TÜV testing center. |
159.90 €
*
Currently unavailable |
1 - 30 of 88 results |
|