Ignitions Ignition parts

Flywheel wedge for 4mm for Honda and replica 12V ignitions, original Honda

NGK spark plug BR8ES

→ Dimensions: Key width 20.8mm,

Thread diameter 14.0mm,

Thread length 19.0mm

Nut for magnet wheel

→ Original Honda 10x1.25

NGK spark plug CR7HSA Skyteam Dax Monkey Skymax 125 etc.

Small O-ring for ignition base plate Original Honda spare part (2 pieces are required each) these are the seals for the 2 screws)

→ Note: all O rings for ignition are in the shaft seal set ART 200269

Holding pliers, locking tool for pole fly wheel.

To block and hold the pole wheel. Max. opening width 10cm

Flywheel Nut for YX engines and other with wide Flange

→ 12 x 1.25 thread

Stator seals for many engines 50-125cc, like Honda Monkey, SS50, Dax, Lifan, Zongshen

Ignition for ATV (E-Start), Scooter Gy 6 etc.

4-pin plug (3 pins occupied) and 2 individual cables for ignition power and pickup

→ Dimensions: klicke here

Ignition Cover yx 160ccm u.a.

repair parts for Starterclutch

→ for Zongshen 190, 212, daytona 190

45 km/h CDI installed as standard on the Kepspeed Dax (open by pulling out the plug)

→ also suitable for larger engines, reduces the speed to approx. 6000 rpm

12 volt CDI ignition with crankshaft adapter suitable for 6 volt Dax, Monkey, SS50, Chaly

→ Only fits engines with long crankshaft journals!

→ Does not fit engines that have crankshafts with short journals.

Original Honda magnet wheel wedge 3mm for 6 volt engines

Ignition coil for euro 5 Skyteam

Standard CDI for Daytona Anima FSM engine

→ Please note: This CDI only fits FSM engines

Ignition coil suitable for Honda CB, CY, XL and others

Rectifier 3 pin, 6V

12 volt mini ignition with Takegawa flywheel suitable for 6V engines, only suitable for engines with a crankshaft with long crankshaft journals

→ When converting a 6V engine, you will also need 12V CDI, ignition coil rectifier (see below under accessories)

Daytona Anima 2nd version CDI for Anima 4 valve engine

→ Be sure to follow the instructions: Does not fit Daytona FSM engines

→ Approximately 1 hp more power compared to the first version according to the manufacturer

Spark plug Denso CPR8EA9 U24EPR9

Spark plug Denso CR7HSA Skyteam Dax Monkey Skymax 125 etc.

Daytona ignition connection cable

→ Fits the ignition that is installed as standard on the Daytona125/Zongshen125 and also on the 190 Anima engine without starter, does not fit on the FSM engine

Collar nut m10 x 1.25 for crankshaft shock absorber mount etc.

→ available in gold and silver

3 phase rectifier for 100 watt ignition

→ 7 connection cables: 3 x yellow, black, red, green, white

Ignition for Kinroad Minichopper XT50, ATV, Yamasaki etc. for overhead starter with pole wheel, without freewheel (see accessories below)

Ignition for 50-110ccm engines with overhead starter

→ fits for Kinroad Minichopper Romet, ATV, Yamasaki, etc.

3 phase rectifier for 100 watt ignition

→ 6 connection cables: 3 x yellow, black, red, green