Ignitions Ignition parts

Ignition for ATV (E-Start), Scooter Gy 6 etc.

4-pin plug (3 pins occupied) and 2 individual cables for ignition power and pickup.

Ignition can also be used for many other Estart engines. The plugs to the wiring harness may then have to be connected individually.

Coil outer diameter: 83mm

Distance between mounting holes: 41mm

Inner diameter: 29mm

Flywheel wedge for 4mm for Honda and replica 12V ignitions original Honda

NGK spark plug BR8ES

Please note the dimensions, this spark plug does not fit standard Dax Monkey Honda Skyteam etc. Engines !

Key width 20.8mm

Thread diameter 14.0mm

Thread length 19.0mm

repair parts for Starterclutch, for Zongshen 190, 212, daytona 190

Ignition Cover yx 160ccm u.a.

Nut for magnet wheel Original Honda 10x1.25

Small O-ring for ignition base plate Original Honda spare part (2 pieces are required each) these are the seals for the 2 screws)

Note: all O rings for ignition are in the shaft seal set ART 200269

NGK spark plug CR7HSA Skyteam Dax Monkey Skymax 125 etc.

Ignition coil Dax Monkey 12v etc. (bracket for screwing)

Ignition coil with rubber holder and 2 connector plugs also available in the shop, see accessories below

Repro ignition coil for Honda 6 Volt Dax

Honda comparison number is 30512-126-921

Original Honda magnet wheel wedge 3mm for 6 volt engines

Ignition coil for euro 5 Skyteam

45 km/h CDI installed as standard on the Kepspeed Dax (open by pulling out the plug), also suitable for larger engines, reduces the speed to approx. 6000 rpm

Daytona ignition for FSM engines
For a suitable magnet wheel, see accessories below

12 volt CDI ignition with crankshaft adapter suitable for 6 volt Dax, Monkey, SS50, Chaly

Only fits engines with long crankshaft journals! If you have any questions/uncertainties, please feel free to contact us

Does not fit engines that have crankshafts with short journals.

To convert the vehicle to 12 volt ignition, you will need a CDI, 12V ignition coil, 12V rectifier, adapter cable, 12V horn, 12V battery and 12V bulbs.

(we also offer a complete kit; bulbs must be ordered individually)

Ignition coil suitable for Honda CB, CY, XL and others

Standard CDI for Daytona Anima FSM engine

Please note: This CDI only fits FSM engines

Rectifier 3 pole 6V

Racing CDI 5 pin + ignition coil for Skyteam Dax Monkey Honda etc.

Daytona Anima 2nd version CDI for Amima 4 valve engine Be sure to follow the instructions. Does not fit Daytona FSM engines

Approximately 1 hp more power compared to the first version according to the manufacturer

Collar nut m10 x 1.25 for crankshaft shock absorber mount etc.

Spark plug Denso CPR8EA9 U24EPR9

Spark plug Denso CR7HSA Skyteam Dax Monkey Skymax 125 etc.

Cable holder for ignition cover Zongshen 190/212 engine

Open AC CDI for many 4-stroke scooters, also suitable for Monkey Dax etc.

However, a suitable adapter cable to a 5-pin plug is usually required (see accessories below)

Ignition for Kinroad Minichopper XT50, ATV, Yamasaki etc. for overhead starter with pole wheel, without freewheel (see accessories below)

Ignition for 50-110ccm engines with overhead starter

fits for Kinroad Minichopper Romet, ATV, Yamasaki, etc.

3 phase rectifier for 100 watt ignition

7 connection cables: 3 x yellow, black, red, green, white

12 volt mini ignition with Takegawa pole wheel with early adjustment suitable for 6 V engines, only suitable for engines with a crankshaft with long crankshaft journals

When converting a 6 V engine, you will also need 12 V CDI, ignition coil rectifier (see below under accessories)