Kepspeed parts

Kepspeed bench, diamond pattern, suitable for Skyteam Skymax with 5.5 liter frame.

45 km/h CDI installed as standard on the Kepspeed Dax (open by pulling out the plug), also suitable for larger engines, reduces the speed to approx. 6000 rpm

Bottom stainless steel exhaust for Monkey with E-No. (E-No. valid for Kepspeed Monkey 125ccm) without cat (for suitable cat see below under accessories)

The exhaust is supplied with a lambda sensor adapter, but there is also a screw included to close the connection on the manifold

The system does not fit the Euro 4 / 5 125ccm models without adjustment work because the manifold hits the brake pedal
(When installing, the holder for the exhaust would have to be bent (longer and to the side, as shown in the last pictures)

The standard Monkey also requires at least one + 4 swing arm with 8 inch studded tires

Dax swingarm from Kepspeed in standard length

Dimensions of version +0
Total length: approx. 340mm
Length from center of swing arm axle - center of wheel mount: approx. 300mmRequired rear axle length: at least 210mm (12mm)

The swing arm is registered in the COC of the Kepspeed Custom Dax and can therefore usually be registered in other vehicles without any problems. Please write to us about this and we will be happy to send you the COC by email.

Very high quality black Kepspeed aluminum swingarm for Dax + 6 cm for Honda Dax / Skyteam Dax / Skymax

The included axle is the rear wheel axle

Dimensions of version +6
Total length: approx. 405mm
Length from center of swing arm axle - center of wheel mount: approx. 355mm

Not suitable for the 125cc Skymax with Euro 4/5 with disc brakes!

The swing arm is registered in the COC of the Kepspeed Custom Dax and can therefore usually be registered in other vehicles without any problems. Please write to us about this and we will be happy to send you the COC by email.

Low Monkey seat from Kepspeed,

available with white, gray or black piping, diamond pattern

Keihin (China) carburetor PE28 for engines from 160-190cc

Connection to the intake flange: approx. 35mm
Air filter connection: approx. 48mm
Total length: approx. 83mm
Total height: approx. 135mm

HD: 118
ND: 40

offset sprocket kit from Kepspeed for the wide Dax and Monkey Kepspeed swingarms, normal sprockets can be used

overhead Kepspeed exhaust in stainless steel with E-No.

E-No. for 50cc engine

Exhaust is not suitable for large engines due to the short manifold

There is no catalytic converter, so the exhaust is not permitted for use on public roads and is also significantly louder than permitted, as only a "strainer" is installed as the DB Killer.

The 58mm DB Killer from Kepspeed fits

ALU clutch cover from Kepspeed, available in black, gold, blue, red or silver

Kepspeed under engine exhaust stainless steel

General note: The item offered is an item without e-marking / tuning item that is intended for racing purposes and customizing. Therefore, use on public roads is not permitted. The attachment leads to the expiry of the operating license unless it is entered into the vehicle documents by an approved TÜV testing center.

Aluminum crash bar set for Monkey from Kepspeed (installed on Kepspeed Monkey in the picture)

Sprocket from Kepspeed for Dax for screwing made of high-strength aluminum in various sizes

Kespeed Classic exhaust with snake manifold suitable for engines without electric start.

Heat protection plate with e-number also available in the shop.

General note: The item offered is an item without e-marking / tuning item that is intended for racing purposes and customizing. Therefore, use on public roads is not permitted. The attachment leads to the expiry of the operating license unless it is entered into the vehicle documents by an approved TÜV testing center.